Blog

Measure the length and width of your driveway in feet. Multiply the length by the width to get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.

Driveway Layers

A gravel drive should have a first layer of baseball-sized stones at least 4 inches deep. According to Tim Carter of AskTheBuilder.com, each layer thereafter should be 4 inches thick and in gradually smaller stone.

There are approximately 1.4 tons of stone per cubic yard. How Much Does A Ton Of Gravel Cover? When laying the recommended gravel-layer depth of 4", then a ton of pea gravel covers an area of 40 to 50 square feet.

Pea gravel costs $28 per ton when ordering at least 24 tons, or $45 per ton in smaller quantities. The bulk-rate converts to $29 to $40 per cubic yard if you pick it up yourself from a local quarry or $1 to $3 per cubic foot.

A ton of gravel will cover approximately 100 square feet, 2 inches deep.

Truck Load of Gravel Cost. A truck load of gravel costs $1,350 or more with a 10-yard minimum, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.

Full-size Pickup Trucks: Can usually handle 2 cubic yards of soil, 2-3 cubic yards of mulch, and 1 cubic yard of stone or gravel. Small Pickups and Trailers: Can usually handle 1 cubic yard of soil to maybe 1½ of mulch.

Typically, larger dump trucks can carry about 28,000 pounds or about 14 tons. On average, smaller dump trucks can transport around 13,000 to 15,000 pounds or 6.5 to 7.5 tons.

With proper care and maintenance, a gravel driveway can last up to 100 years. The beauty of gravel is that it can be repaired and replenished on an ongoing basis. By contrast, wear and damage to asphalt and concrete driveways are difficult to remedy and replacement is often more cost-effective than extensive repairs.21 янв. 2022 г.

This very coarse, crushed, washed, clean gravel is primarily 2″ in size with a top size of 2-1/2″. It is good for establishing roads over semi-firm soil conditions or topping extremely muddy drives. This product is too coarse to shovel by hand.

A ton of gravel will cover approximately 100 square feet, 2 inches deep.

Understanding Size and Coverage

Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.

Pea gravel is generally more expensive than organic mulches and, because of its weight, it is more difficult to install. ... Your soil may retain moisture better with pea gravel than with no mulch at all, but the rock is not effective in maintaining even soil temperatures.

The cost of gravel ranges from $10 to $50 per ton, $15 to $75 per yard, $1 to $3 per square foot, or $1,350 per truck load depending on the rock type, volume, and travel distance.

In this regard, “how much area does a yard of gravel cover?”, their coverage depends on how thick or deep you plan on placing the gravel, for 1 inch depth, a yard of gravel can cover about 324 square feet area, for 2″ depth, it will cover around 162 square feet area, for 3″ depth, it will cover around 108 square feet ...

• Plain pea gravel will cost about $35 to $42 per ton, while a decorative colored pea gravel can cost anywhere from $50 to $85 per ton. Since a ton is equal to 2,000 pounds, 2,800 pounds can cover one cubic yard or 27 cubic feet.

• To calculate how much gravel is needed, measure the width and breadth of the area in feet, and determine the depth desired. Multiply the length times the width times the depth for the number of cubic feet, then divide that number by 27 to determine the needed cubic yards.

• You'll generally need to contact a landscaping supplier to purchase this quantity. The price will fluctuate by location and is based on the distance from a quarry. The general range for a cubic yard of plain pea gravel is about $30 to $35 , and a ton will cost about $40 to $45 .

• Along with the gravel you will need sand. A layer of about 1 inch over the gravel is about right. However, some of the sand will sift down into the gravel. Allow about a third as much in cubic volume for sand as you buy of gravel. For 1.5 cubic yards of gravel, get about one-half cubic yards of sand.

Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.

Pea gravel is popular gravel for driveway aesthetics. It's made up of round, small stones that can come in many different colors. This type of gravel will easily migrate and spread under the weight of vehicles, though, and needs to be stabilized for long-term, maintenance-free usage.

Generally speaking, you should add about 1 pound of substrate per gallon of water. This means that for a 5-gallon fish tank, a safe bet would be 5 pounds of gravel. Similarly, for a 20-gallon fish tank, roughly 20 pounds of gravel would suffice.

A 50-pound bag of pea gravel is equivalent to 0.5 cubic foot, so two 50-pound bags cover 1 cubic foot. Knowing that a 50-pound bag of pea gravel averages 0.5 cubic foot makes the calculation easy — and one most smartphone calculators can complete.

Gravel Prices Per Ton. Bulk crushed stone and gravel prices are $10 to $50 per ton on average. Road base costs $18 to $30 per ton, and plain pea gravel or limestone costs $28 to $45 per ton. Buying gravel in small quantities costs over $100 per ton.

The average cubic yard of gravel costs between $40 and $55. Expect to pay $50 to $65 per ton. Purchasing by the ton is often cheaper on the whole because this is considered buying in bulk.Feb 22, 2021

A truck load of gravel costs $1,350 or more with a 10-yard minimum, including delivery and spreading based on the rock type, amount, truck size (double or tri-axle), and travel distance. Most rock-fill jobs use a 3-man crew plus a tractor for $46 per hour that spread 12 cubic yards per hour.

Cheapest gravel for driveways. The cheapest gravel for driveways is crusher run, crushed shells, crushed concrete, slate chips, recycled asphalt, and pea gravel, which all cost $15 to $30 per yard, or less than $1 per square foot when purchased in bulk from a quarry.Aug 18, 2021

A ton of gravel will cover approximately 100 square feet, 2 inches deep.

Understanding Size and Coverage

Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.

A commonly used gravel size for driveway base layers is #3 gravel. This rock is generally 1-2 inches in diameter and does double duty by establishing a solid, reliable foundation and providing adequate drainage; both critical factors in driveway construction.

The ideal thickness of each layer is between 4 to 6 inches. The middle layer should also be angular stones about 2” to 3” in diameter such as our #2 Bluestone. Since the material is angular it locks together providing traction and a stable foundation.Jan 18, 2017

Regarding this, how many square feet does 5 tons of gravel cover?”, according to Imperial or US customary measurement system, in general, 5 tons of gravel can be sufficient to cover approximately 540 square feet for 2 inch standard depth of construction project like roadways, pedestrian or others structure.

Pea gravel consists of small stones, typically found near water, and has a smooth surface due to weathering. ... You'll find this versatile hardscaping material covering driveways, water drains, paths, patios, filling spaces between pavers, and even in playgrounds.Jun 3, 2021

Gravel is a whole lot cheaper than concrete, asphalt, or another paved surface. It can cost less than 1/2 of paved driveways.Sep 15, 2020

This primarily 1″ crushed, washed gravel with a top size of 1-1/2″ is often used for drainage around perforated pipe, under concrete slabs, and as a coarse driveway topping for soft, very muddy driveways. Suitable as a coarse driveway topping.

How Wide Are Residential Driveways? Primarily, most professionals recommend that you install a 10 feet to 12 feet wide driveway. The standard driveway width for an SUV or conventional pickup truck is 10 feet. Anything less than 10' wide will likely present difficulties for drivers, even in smaller vehicles.Dec 30, 2019

Is it really necessary to put fabric under my gravel driveway? Yes, if you want your driveway to last. Having geotextile fabric under your gravel driveway will prevent you from continually needing to add more aggregate base to your road since the rock will drop into the subgrade layer.May 15, 2020

Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.

Using a membrane underneath you gravel driveway or path will prevent weeds whilst allowing natural elements to permeate through to the soil beneath. It also helps to keep your gravel clean by creating a barrier.Oct 17, 2016

• The best types of gravel for a driveway are as follows: Road gravel driveways: Road gravel is the most affordable type of driveway gravel. Its makeup is clay and small stones, typically crushed or naturally angular stones that hold together better than round, smooth stones.

• When you think of a gravel driveway, you may imagine a sleepy, dusty lane that leads to a quaint rural cottage or farmhouse on a lonely country road. In reality, gravel is equally at home in rural, suburban, or urban environments, and its durability, affordability, and ease of installation make it a smart paving option for driveways.

• Rock Mulch & More delivers aggregate supplies like 57 limestone gravel, concrete sand, and much more in the Pittsburgh region. Whether you're working on a garden project, building a driveway, or even preparing a swimming pool, we have the supplies you need. All of our limestone, sand, and gravel products are below, with their common uses.

• Buy gravel in bulk at major home retailers such as The Home Depot or Lowe's. Bulk gravel is also sold at online specialty stores such as The Rock Pile and Braen Stone. The Home Depot sells different types of gravel suitable for driveways, walkways and gardens.

Find the best Gravel Companies near you on Yelp - see all Gravel Companies open now. Explore other popular Home Services near you from over 7 million businesses with over 142 million reviews and opinions from Yelpers.

Road base costs $18 to $30 per ton, and plain pea gravel or limestone costs $28 to $45 per ton. Buying gravel in small quantities costs over $100 per ton. It takes 1.4 tons of stone per cubic yard. Bulk gravel costs $15 to $75 per yard on average. Crushed concrete, sand and gravel mix, and crushed shells are the cheapest stones at $15 per yard.

#8 Washed River Gravel is commonly used as a top coating for gravel walks and driveways We recommend installing a few inches of a larger gravel such as #57 Limestone Gravel or #57 Washed River Gravel and then adding a coating of an inch or so of the #8 Washed River Gravel.

Whether used for decoration or construction, bulk gravel from Georgia Landscape Supply provides exceptional quality at affordable prices. We carry a huge inventory of gravel that lets you finish any project you’re working on, from walkways and woodland patios to driveways and French drains.

Regarding this, “how many yards in a ton?”, generally for estimating purpose 1 yard of gravel weighs around 3000 pounds and 1 US ton = 2000 pounds, so yards in a ton = 2000/3000 = 0.66 cubic yards, therefore, there are 0.66 yards in a ton.

• Gravel & Stone Delivered to Maryland and Northern Virginia Saunders Landscape Supply offers landscaping stone and gravel delivery in Northern Virginia and Maryland. From very small pea gravel to large landscaping stones, river wash gravel, blue stone, crushed stones, recycled concrete and more, all for sale and immediate delivery in MD & VA.

• Saunders Landscape Supply offers landscaping stone and gravel delivery in Northern Virginia and Maryland. From very small pea gravel to large landscaping stones, river wash gravel, blue stone, crushed stones, recycled concrete and more, all for sale and immediate delivery in MD & VA.

• Pave your way to success with our list of top-rated Sand and Gravel Suppliers in ME. On Yell.com you'll find the best sand and gravel providers who supply materials for both home and commercial groundwork including driveways, foundations and decorative aggregates.

• Gravel and stone landscaping gives your outdoor space a rustic charm that transitions visitors seamlessly from your greenery into your home. You can get a simple, casual look for a gravel patio or a natural look for a functional structure like a flower bed made from stone.

Pave your way to success with our list of top-rated Sand and Gravel Suppliers in ME. On Yell.com you'll find the best sand and gravel providers who supply materials for both home and commercial groundwork including driveways, foundations and decorative aggregates.

At Buildbase we have a wide variety of loose aggregates. These aggregates, such as MOT type 1, ballast, gravel / shingle and building sand are sold from our aggregate bays at our branches by the scoop and are then loaded into your vehicle using our mini dumper.

At Direct Gravel Supplies, you’ll find a great range of decorative garden gravel and stone. If its not quite what you’re looking for please contact us and we will do our best to source it for you. Don’t struggle loading a dozen bags into your car at your local DIY store, get direct gravel supplies to deliver manageable size bags direct to you!

You will need: 24.93 bulk bags of this aggregate type. You will need: 935.00 mini bags of this aggregate type. We cannot be held contractually responsible for any surplus or shortfall found on site. Gravel can help to instantly transform your outside space, whether it is used for a garden boundary, a driveway, a path or for a pond.

Gravel or Crushed Rock Delivery Prices – Generally, Minus crushed rock costs $12-$35 per cubic yard while clean crushed rock costs $30-$50 per cubic yard. For delivery and spreading, costs will double. Gravel or Crushed Stone delivery cost also depend on the quantity that you order, more quantity mean less price.

Spreading gravel costs $10 to $25 per cubic yard or $46 per hour depending on the job size, rock type, and crew efficiency. Large jobs with a 3-person crew and a tractor spread 12 cubic yards per hour. Smaller landscape projects spread 2 to 4 yards by hand for $22 per cubic yard. Find landscapers near you to help.

6 tons of gravel = 0.714 ×6 = 4.284 cubic yards, 7 tons of gravel = 0.714 ×7 = 4.998 cubic yards, 8 tons of gravel = 0.714 ×8 = 5.712 cubic yards, 9 tons of gravel = 0.714 ×9 = 6.426 cubic yards and 10 tons of gravel = 0.714 ×10 = 7.140 cubic yards.

A ton of gravel will cover approximately 100 square feet, 2 inches deep.

• Some shrubs grow well in gravel gardens. Due to the difficulty of digging and planting within gravel gardens, shrubs provide ongoing beauty without disturbing the soil every year. Conifers and low-growing evergreens provide color to gravel areas.

• Gravel is found naturally, mostly in lake, river, and ocean beds, where the constant movement of the water and waves keeps the gravel from settling and fusing with other rocks; sand is a form of micro-gravel, being tiny stones worn down by constant motion.